Led Driver Oti Dali 90/220-240/1a0 Lt2 L 4052899494268
Osram
Part No
LEDOTIDALI901A0LT2L
Led Driver Oti Dali 90/220-240/1a0 Lt2
EAN: 4062172082327
Product family benefits:
Fully programmable via software (DALI Interface)
Flexible current setting (LEDset2)
Lifetime: up to 100,000 h (temperature at Tc = 65 °C, max. 10 % failure rate)
High-quality dimming of 1…100 % by amplitude dimming (except 80 W versions)
High quality of light thanks to <1% output ripple current
Very high efficiency
Very low standby power consumption: < 0.25 W
Fulfill safety requirement due to overload, overtemperature, Hot Plug protection
Versatile scope of application due to OSRAM DALI Technology:
Easy to use in corridors and restrooms because of three-level Corridor function
Touch DIM application: easy to control via pushbutton or sensor
Energy efficient Touch DIM operation due to automatic switch-off at sufficient residual light
Suitable for emergency Installations (acc. to EN 60598-2-22 and IEC 61347-2-13, appendix J) thanks to DC detection (0 Hz, pulsating DC), on/off switchable
Feedback of power consumption and operating hours (Fit for SMART GRID)
Suitable for buildings according to EPBD/BREEAM/LEED due to automatic Constant Lumen Output setting
Luminaire information for easy maintenance
Areas of application:
Linear lighting for office, education, industry, storage areas and retail
Installation in emergency lighting systems according to IEC 61347-2-13, appendix J
Suitable for luminaires of protection class I
Electrical data:
Nominal input voltage: 220…240 V
Mains frequency: 50…60 Hz
Input voltage AC: 198…264 V
Input voltage DC: 176…276 V
Current set: DALI / LEDset / Programmable
Total harmonic distortion: < 10 %
Power factor λ: > 0.95
Efficiency in full-load: 94 %
Device power loss: 9.0 W
Networked standby power [GMS]: ≤0.30 W
Inrush current: 25 A
Max. ECG no. on circuit breaker 10 A (B): 15
Max. ECG no. on circuit breaker 16 A (B): 24
Max. ECG no. on circuit breaker 25 A (B): 29
Surge capability (L/N-Ground): 2 kV
Surge capability (L-N): 1 kV
Nominal output voltage: 54…240 V
U-OUT (working voltage): < 250 V
Nominal output current: 250…1000 mA
Output current LEDset open: 125 mA
Output current LEDset shorted: 250 mA
Default output current: 125 mA
Output current tolerance: ±3 %
Output ripple current (100 Hz): < 1 %
Output PSTLM: ≤1
Output SVM: ≤0.4
Nominal output power: 13.5…90 W
Maximum output power: 90 W
Galvanic isolation: Non isolated
Dimensions & weight
Mounting hole spacing, length: 270.0 mm
Product weight: 205.00 g
Cable cross-section, input side: 0.5…1.5 mm²
Cable cross-section, output side: 0.5…1.5 mm²
Wire preparation length, input side: 8.5…9.5 mm
Wire preparation length, output side: 8.5…9.5 mm
Length: 280.0 mm
Height: 21.0 mm
Width: 30.0 mm
Colors & materials:
Casing material: Metal
Temperatures & operating conditions:
Ambient temperature range: -25…+50 °C
Maximum temperature at tc test point: 75 °C
Max.housing temperature in case of fault: 110 °C
Temperature range at storage: -25…85 °C
Permitted rel. humidity during operation: 5…85 %
Lifespan
ECG lifetime: 50000 / 100000 h
Additional product data:
Encapsulated: No
Capabilities:
Programming interface: DALI, LEDset
Dimmable: Yes
Dimming interface: DALI-2 / Touch DIM / Touch DIM Sensor
Dimming range: 1…100 %
Dimming method: Full analogue dimming
Overheating protection: Automatic reversible
Overload protection: Automatic reversible
Short-circuit protection: Automatic reversible
No-load proof: Yes
Intended for no-load operation: No
Max. cable length to lamp/LED module: 2.0 m
Suitable for fixtures with prot. class: I
Suitable for emergency lighting: Yes
Type of connection, input side: Push terminal
Type of connection, output side: Push terminal
DALI-2 Energy Data: Yes
Control interface: DALI
Number of channels: 1
DALI-2 Diagnostic Data: Yes
Programming:
Programming device: DALI magic
Tuner4TRONIC: Yes
Tuner4TRONIC Field App: Yes
Programmable features:
DALI-2 Luminaire Data: Yes
Certificates & standards:
Approval marks – approval: CE / EL / VDE-ENEC / VDE-EMC / EAC / CCC / BIS / RCM
Standards: Acc. to EN 61347-1/Acc. to EN 61347-2-13/Acc. to EN 55015/Acc. to EN 61547/Acc. to EN 61000-3-2/Acc. to EN 62384/Acc. to EN 62386
Type of protection: IP20
Logistical data:
Commodity code: 850440829000
Environmental information:
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration: 14-04-2022
Primary Article Identifier: 4052899160071 | 4052899494268 | 4062172082327
Candidate List Substance 1: Lead
CAS No. of substance 1: 7439-92-1
Safe Use Instruction: The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database: 8ef3bb96-a042-4063-aaed-c1f3754bddc8 | ec44fbf5-a20a-4869-8835-dd899d37b8d9
EAN: 4062172082327
Product family benefits:
Fully programmable via software (DALI Interface)
Flexible current setting (LEDset2)
Lifetime: up to 100,000 h (temperature at Tc = 65 °C, max. 10 % failure rate)
High-quality dimming of 1…100 % by amplitude dimming (except 80 W versions)
High quality of light thanks to <1% output ripple current
Very high efficiency
Very low standby power consumption: < 0.25 W
Fulfill safety requirement due to overload, overtemperature, Hot Plug protection
Versatile scope of application due to OSRAM DALI Technology:
Easy to use in corridors and restrooms because of three-level Corridor function
Touch DIM application: easy to control via pushbutton or sensor
Energy efficient Touch DIM operation due to automatic switch-off at sufficient residual light
Suitable for emergency Installations (acc. to EN 60598-2-22 and IEC 61347-2-13, appendix J) thanks to DC detection (0 Hz, pulsating DC), on/off switchable
Feedback of power consumption and operating hours (Fit for SMART GRID)
Suitable for buildings according to EPBD/BREEAM/LEED due to automatic Constant Lumen Output setting
Luminaire information for easy maintenance
Areas of application:
Linear lighting for office, education, industry, storage areas and retail
Installation in emergency lighting systems according to IEC 61347-2-13, appendix J
Suitable for luminaires of protection class I
Electrical data:
Nominal input voltage: 220…240 V
Mains frequency: 50…60 Hz
Input voltage AC: 198…264 V
Input voltage DC: 176…276 V
Current set: DALI / LEDset / Programmable
Total harmonic distortion: < 10 %
Power factor λ: > 0.95
Efficiency in full-load: 94 %
Device power loss: 9.0 W
Networked standby power [GMS]: ≤0.30 W
Inrush current: 25 A
Max. ECG no. on circuit breaker 10 A (B): 15
Max. ECG no. on circuit breaker 16 A (B): 24
Max. ECG no. on circuit breaker 25 A (B): 29
Surge capability (L/N-Ground): 2 kV
Surge capability (L-N): 1 kV
Nominal output voltage: 54…240 V
U-OUT (working voltage): < 250 V
Nominal output current: 250…1000 mA
Output current LEDset open: 125 mA
Output current LEDset shorted: 250 mA
Default output current: 125 mA
Output current tolerance: ±3 %
Output ripple current (100 Hz): < 1 %
Output PSTLM: ≤1
Output SVM: ≤0.4
Nominal output power: 13.5…90 W
Maximum output power: 90 W
Galvanic isolation: Non isolated
Dimensions & weight
Mounting hole spacing, length: 270.0 mm
Product weight: 205.00 g
Cable cross-section, input side: 0.5…1.5 mm²
Cable cross-section, output side: 0.5…1.5 mm²
Wire preparation length, input side: 8.5…9.5 mm
Wire preparation length, output side: 8.5…9.5 mm
Length: 280.0 mm
Height: 21.0 mm
Width: 30.0 mm
Colors & materials:
Casing material: Metal
Temperatures & operating conditions:
Ambient temperature range: -25…+50 °C
Maximum temperature at tc test point: 75 °C
Max.housing temperature in case of fault: 110 °C
Temperature range at storage: -25…85 °C
Permitted rel. humidity during operation: 5…85 %
Lifespan
ECG lifetime: 50000 / 100000 h
Additional product data:
Encapsulated: No
Capabilities:
Programming interface: DALI, LEDset
Dimmable: Yes
Dimming interface: DALI-2 / Touch DIM / Touch DIM Sensor
Dimming range: 1…100 %
Dimming method: Full analogue dimming
Overheating protection: Automatic reversible
Overload protection: Automatic reversible
Short-circuit protection: Automatic reversible
No-load proof: Yes
Intended for no-load operation: No
Max. cable length to lamp/LED module: 2.0 m
Suitable for fixtures with prot. class: I
Suitable for emergency lighting: Yes
Type of connection, input side: Push terminal
Type of connection, output side: Push terminal
DALI-2 Energy Data: Yes
Control interface: DALI
Number of channels: 1
DALI-2 Diagnostic Data: Yes
Programming:
Programming device: DALI magic
Tuner4TRONIC: Yes
Tuner4TRONIC Field App: Yes
Programmable features:
DALI-2 Luminaire Data: Yes
Certificates & standards:
Approval marks – approval: CE / EL / VDE-ENEC / VDE-EMC / EAC / CCC / BIS / RCM
Standards: Acc. to EN 61347-1/Acc. to EN 61347-2-13/Acc. to EN 55015/Acc. to EN 61547/Acc. to EN 61000-3-2/Acc. to EN 62384/Acc. to EN 62386
Type of protection: IP20
Logistical data:
Commodity code: 850440829000
Environmental information:
Information according Art. 33 of EU Regulation (EC) 1907/2006 (REACh)
Date of Declaration: 14-04-2022
Primary Article Identifier: 4052899160071 | 4052899494268 | 4062172082327
Candidate List Substance 1: Lead
CAS No. of substance 1: 7439-92-1
Safe Use Instruction: The identification of the Candidate List substance is sufficient to allow safe use of the article.
Declaration No. in SCIP database: 8ef3bb96-a042-4063-aaed-c1f3754bddc8 | ec44fbf5-a20a-4869-8835-dd899d37b8d9
| Weight | 220g |
|---|
Customer Questions
Write Your Own Review
For price, stock availability and other information about this product, please contact us using the form below.
For price, stock availability and other information about this product, please contact us using the form below.
sgm_clp_1 div for segmentify