Crating Hardware

Series 6 Air-Dampened Pallet Cushions.

Cushion Height: 2-11/16" / 68mm
Cushion + Spacer = 3-3/4” / 95mm

Use Spacer 6228

Our Pallet Cushions are the most economical and reliable way to replace and upgrade wooden skid runners on pallet crates, eliminating the need for costly air-ride trucks, these air-dampened polyethylene cushions are easily attached to pallets or crates to provide a high level of protection from shock and vibration.
Don’t risk shipment damage by shocks, drops, and impact during transit or handling.

Easy to Install
The pre-installed t-nut, with a 5/16”-18 UNC thread, protrudes out of the cushions for easy location into the mounting hole and fast installation. (Also available with an M8 threaded t-nut)
The pallet cushions are mounted directly on a pallet or container base with a simple bolt.

Reusable
The pallet cushions can be easily removed and mounted again on another pallet.
Simple and Practical
Our Series 6 Pallet Cushions, once fitted with the 6228 Spacer, create a four-way 3-3/4” space under the pallet, which makes it easy to load and unload with a pallet jack and forklift.

Resistant and Durable
Our Pallet Cushions have been through rigorous stress tests. They can be dragged on concrete and joints for 3000 feet, at maximum load, with only minimal wear noted. Suitable for use between -104°F and +130°F (-40°C to + 54°C) and chemical resistant.

Pallet Cushion Spacer to Suits 6035 - 6225 Pallet Cushions.

Spacer Height: 1-1/16” / 26.8mm
Increases cushion height to 3-3/4” / 95mm

Series 7 Air-Dampened Pallet Cushions.

Cushion Height: 2-7/8" / 73mm
Cushion + Spacer = 4” / 102mm

Use Spacer 7228

Our Pallet Cushions are the most economical and reliable way to replace and upgrade wooden skid runners on pallet crates, eliminating the need for costly air-ride trucks, these air-dampened polyethylene cushions are easily attached to pallets or crates to provide a high level of protection from shock and vibration.
Don’t risk shipment damage by shocks, drops, and impact during transit or handling.

Easy to Install
The pre-installed t-nut, with a 5/16”-18 UNC thread, protrudes out of the cushions for easy location into the mounting hole and fast installation. (Also available with an M8 threaded t-nut or without t-nut)
The pallet cushions are mounted directly on a pallet or container base with a simple bolt.

Reusable
The pallet cushions can be easily removed and mounted again on another pallet.
Simple and Practical
Our Series 7 Pallet Cushions, once fitted with the 7228 Spacer, create a four-way 4” space under the pallet, which makes it easy to load and unload with a pallet jack and forklift.

Textured Finish
The Series 7 Pallet Cushions has a textured finish for a better grip.

Resistant and Durable
Our Pallet Cushions have been through rigorous stress tests. They can be dragged on concrete and joints for 3000 feet, at maximum load, with only minimal wear noted. Suitable for use between -104°F and +130°F (-40°C to + 54°C) and chemical resistant.

Pallet Cushion Spacer to Suits 7035 - 7225 Pallet Cushions.

Spacer Height: 1-1/8" / 28.6mm
Increases cushion height to 4" / 102mm

Pallet Collar Hinge with Removable Pin

220mm x 87mm x 1.5mm / 8.66" x 3.43" x 1/16"

Strap Hinges

Large pallet skid.

116mm x 90mm / 4.57" x 3.54"

Allows cases without wheels or with removable wheels to be handled with fork lift or pallet truck.

Heavy Duty Corner Protector, PVC with Steel Insert.

Large #4 Spring-Lock.

Medium #3 Spring-Lock.

Small #2 Spring-Lock.

Cleat Lock #1 with Dimples

Cleat Lock #2 with Dimples

Cleat Lock #2 without Dimples

ShockWatch® 2 Impact Indicators are tamper-proof single-use, go/no-go devices that determine if fragile products have been dropped during transit or in storage.
The indicators are not armed until activated by the user.
Turn bright red when an impact beyond a specific G-force threshold has occurred.

Each ShockWatch® 2 has a unique identifier to support traceability.

The Warning Label fits over the ShockWatch® and shows what to do if the impact detection device has been activated.
Warning Label Dimensions: 114.3mm x 146.05mm / 4.5" x 5.75"

Not Available in the USA

The TiltWatch XTR® is a single-use tip indicator used to monitor goods that must remain upright. It turns red if the package is tilted past 80°. However, it remains unaffected by movement due to normal handling conditions.

The warning label fits over the Tiltwatch XTR® and shows what to do if the tilt detection device has been activated.
Warning label dimensions: 146mm x 222.25mm / 5.75" x 8.75"

Heavy Duty 152.4mm / 6" Padlock Hasp.
Comes with Staple.

Large Surface Mount Twist Latch. Flat Cam. Spring-Loaded.

Use Keeper Plate 0371 (Not Included)

Surface mount twist latch protector plate with protective ridges.

For use with 1/2" plywood.

Works with with large twist latches 7536, 7538 and 7568.

Also available with Latch Pre-Riveted Latch 2017-7568

Multi-position surface mount twist latch protector plate with protective ridges. (Latch not included)

The multiple mounting hole patterns enable the latch to operate with catch plates when used with 3/8", 1/2" or 3/4" plywood.

Works with large twist latches 7536, 7538 and 7568.

Large Surface Mount Twist Latch 7568 Pre-Riveted into 2017 protector plate with protective ridges.

2017 protector plate also sold separately
Use Keeper Plate 0371 (Not Included).

Small Surface Mount Twist Latch. Padlockable.

Use Keeper Plate 0334 (Not Included).

Large Surface Mount Twist Latch. Flat Cam.

Use Keeper Plate 0371 (Not Included)

Large Surface Mount Twist Latch. Padlockable. Spring-Loaded.

Use Keeper Plate 2011 (Not Included)

Large Surface Mount Twist Latch. Spring-Loaded.

Use Keeper Plate 0371 (Not Included)

Large Surface Mount Twist Latch.

Use Keeper Plate 0371 (Not Included)

Small Surface Mount Twist Latch with Exposed Mounting Hole. Flat Cam.
Use Keeper Plate 0334 (Not Included).

Small Surface Mount Twist Latch. Flat Cam. Spring-Loaded. Exposed Mounting Hole.

Use Keeper Plate 0334 (Not Included).

Medium Twist Latch. Spring Loaded.

Keeper Plate Not Included

Medium Latch with Lid Catch Plate.

For use with wooden crate panels 18mm / 11/16" thick.