DALI to Mains converter for up to 300W LED retrofit loads 86458619-300U
Lunatone
Part No
LEDDALIPD300WRLC
Phase Dimmer with DALI control input (DALI to mains converter)
White cable clamps, for independent installation, are included.
This version is the 86458619-300U.
Suitable only for LED retrofit lamps.
NOT suitable with any other type of LED (constant current or constant voltage drivers) or non-LED loads.
Product features:
Designed and made in the EU
Universal dimmer (RLC - trailing and leading edge)
Min 10W, Max 300W
Compact housing for back box installation
Looking for a smaller wattage, more cost effective, version? Check-out the Lunatone 25W LEDDALIPD25WRLC version.
Product family overview:
Suitable for dimming of 230V LED-retrofit-bulbs via DALI (Device Type 4 from firmware 3.0 and higher)
Different
types for loads from 3W to 25W (PD) for back box installation and for
10-300W (PD300) for remote ceiling and din rail
Trailing edge phase cut dimmer for resistive and capacitive loads,
leading edge phase cut dimmer for resistive and inductive loads as well
available as universal dimmer
types for loads from 3W to 25W (PD) for back box installation and for
10-300W (PD300) for remote ceiling and din rail
Trailing edge phase cut dimmer for resistive and capacitive loads,
leading edge phase cut dimmer for resistive and inductive loads as well
available as universal dimmer
Conversion of the DALI dim level into a phase cut controlled voltage (trailing/leading edge)
The minimum dim level can be set via DALI (MIN LEVEL)
Additional operating mode as switch (DT7 compliant) available with firmware 3.5 and higher
The module represents a DALI-line client and therefore it has its own DALI-address.
Double DALI terminals - the DALI signal line is connected through.
Article number: 86458619-300U (RLC)
Input type: Mains
Marking terminals: L, N
Rated input voltage: 220-240Vac
Input voltage frequency: 50-60 Hz
Max. input power: 300W
Input: DA, DA
Input type: DALI, supply
Marking terminals: DA, DA
Input voltage range: 9,5V … 22,5V
Max. current consumption DALI: 6mA
Number of DALI addresses: 1
Output: L‘, N
Output type: trailing/leading edge phase cut of mains
Marking terminals: L‘, N bzw
Output voltage: like input L,N
Phase cut angle: 0°-180°
Output voltage frequency: like input L,N
Max. output current: 1.45A Eff ac
Load range: 10-300W
Max. length between device and luminaire: 50m
Insulation data:
Impulse voltage category: II
Pollution degree: 2
Rated insulation voltage: reinforced isolation
Insulation test voltage: 3000Vac
Environmental conditions:
Storing and transportation temperature: -20°C … +75°C
Operational ambient temperature: -20°C … +60°C
Rel. humidity, none condensing: 15% … 90%
General data:
Mounting: built-in, integration in protection class II devices
Rated max. temperature tc: 65°C
Expected life time @tc: 50000h
Protection class: II in intended use
Protection degree housing: IP40
Protection degree terminals: IP20
Terminals:
Connection type: spring terminal connector
Wire size solid core: 0,5 … 1,5 mm2 (AWG20…AWG16)
Wire size fine wired: 0,5 … 1,5 mm2 wire (AWG20 … AWG16)
Size using wire end ferrule: 0,25 … 1 mm2
Stripping length: 8,5 … 9,5mm / 0,33 … 0,37inch
Locking torque: -
Actuation type: Push Button
Dimensions and weight:
Width: 30.16mm
Height: 21.60mm
Length: 120.20 mm
Product weight: 61 g
Standards:
DALI: EN 62386-101, EN62386-102, EN62386-205
EMC: EN 61547, EN 50015 / IEC CISPR15
Safety: EN 61347-2-11, EN 61347-1
Markings: ENEC-11, CE
| Weight | 61g |
|---|
Customer Questions
Write Your Own Review
For price, stock availability and other information about this product, please contact us using the form below.
For price, stock availability and other information about this product, please contact us using the form below.
sgm_clp_1 div for segmentify